![]() ![]() Wiring a GFCI Outlet with a Ordinary Outlet / Receptacle It means, the light switch is not GFCI protected and will operate as a normal circuit. In the second diagram, the light switch is connected to the line terminals of GFCI. This way, the switch and light bulb is GFCI protected. In the first diagram, the single way switch and light bulb is connected to the load terminal of GFCI. Related Post: How to Wire GFCI Combo Switch and Outlet – GFCI Switch/Outlet Wiring Diagrams.Let’s see how to protect additional loads by GFCI outlet by the following different methods. In simple words, only two outlets in the GFCI are protected. other outlet, switches and additional load is not protected by the outlet. In the above diagram, Load is not connected to the GFCI i.e. Related Post: GFCI: Ground Fault Circuit Interrupter. There are multiple types of GFCIs like GFCI outlet, GFCI Combo switch and outlet, GFCI Circuit breaker and portable GFCI. GFCI devices are especially useful for cord connected appliances and equipment used outdoors or near water. GFCI as an outlet / receptacle, combo or circuit breaker, automatically cuts off the main power supply within millisecond against electric shock.Ī GFCI is needed to be installed in moisture, water and water pipes or other similar conditions and locations such as bathroom, kitchen, hot tubes, workshop, swimming pool, laundry, l and any other areas where water and electricity are likely to come in contact. GFCI also known as “Ground Fault Circuit Interrupter” is a protective device which automatically detects the ground faults and leakage current and provides personal protection against electrocution. Wiring a GFCI Outlet with Combo Switch – Outlet, Receptacle & Light Switch.Wiring a GFCI Outlet with a Ordinary Outlet / Receptacle.Wiring a GFCI Outlet with a Light Switch.I’m wondering whether the 2014 NEC now require this. I’ve started coming across GFCI receptacles installed at the refrigerator niche in new construction homes. Section 210.12 Arc-Fault Circuit Interrupter Protection Section 210.8(D) Kitchen Dishwasher Branch Circuit This expansion of AFCI requirements continues the long-range objective of whole-house AFCI protection in dwelling units that was sought in the original proposals by Consumer Product Safety Commission in the mid-1990s. Subdivision (A) now recognizes AFCI protection requirements, which have been expanded to kitchens and laundry areas. This section has been revised to require arc-fault circuit interrupters (AFCIs) to be installed in readily accessible locations. The reason is related to different end-of-life failure modes and behavior of newer generation dishwashers as compared to the electromechanical units in the past. Outlets supplying dishwashers are required to be GFCI-protected, which requires a GFCI-protective device installed at the origin of the branch circuit. A new subdivision (D), “Kitchen Dishwasher Branch Circuit,” has been added to 210.8. Requirements for GFCI protection in dwelling unit kitchens have been expanded. In addition, all 125-volt (V), single-phase, 15- and 20-ampere (A) receptacles installed in laundry areas must be GFCI-protected. Note that this requirement applies to bathtubs or shower stalls, regardless of whether they are in a bathroom or not. GFCI protection is now required for receptacles installed within 6 feet of a bathtub or shower stall. The requirements for ground-fault circuit interrupter protection (GFCI) have been expanded for dwelling units. The other four outlets will not work when the GFCI is tripped. I have a tendency to ferret out all issues with a matter before moving on.Įven though the outlets are not working when the GFCI is tripped While, I may sound nit picky or uneducated it’s me wanting to do the job right and have a proper understanding of what’s in the course material. The standard in the book indicates to a new inspector, ie me, that each receptacle should be a GFCI not just upstream of a series of standard receptacles. So, I thought I would consult all of you for verification. But then I read in the course study material for how to perform Residential Electrical Inspections, the statement above. Originally, I thought the set up was correct because all outlets down stream of the GFCI are protected. To protect people, GFCI protection should be installed at all 125-volt, single-phase, 15- and 20-ampere receptacles that serve countertop surfaces. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |